Welcome, Guest. Please login or register.
Did you miss your activation email?
Sign in with Facebook Sign in with Twitter Sign in with Google Sign in with Linkedin Sign in with Microsoft

Hello! Welcome to the Ford and Volkswagen MPV / SUV Forums.
Dedicated forums for the Ford Galaxy, S-Max, C-Max, B-Max and Kuga.
User groups for the SEAT Alhambra, Volkswagen Sharan, Touran, Tiguan and Touareg!

Owners Forums for Ford and Volkswagen MPVs / SUVs

Ford Galaxy S-Max C-Max B-Max Tourneo Connect / Volkswagen Sharan Touran Tiguan Touareg Caravelle / SEAT Alhambra Alteca 

 Mk1 and Mk2 VW Sharan  Mk1 and Mk2 Ford Galaxy  Mk1 and Mk2 SEAT Alhambra  Ford C-Max B-Max  VW Tiguan  VW Touran  Mk3 Ford Galaxy  Mk3 VW Sharan  Mk3 SEAT Alhambra  VW T4 T5 Caravelle Transporter  Ford Tourneo Connect  VW Touareg

We Support:


Recent Forum Topics:

Google Translate:

Author Topic: Ford Galaxy - Muting the parking sensors when a trailer or caravan is attached  (Read 7509 times)

Rated 3 times
- Excellent

Offline Mirez

  • Pondering the next mod...
  • *
  • Posts: 3717
  • Thanked: 154
  • Model: Galaxy Mk2
  • Spec: 03 115PS Ghia
  • First Name: Mark
  • Region: South West
  • Country: United Kingdom
Ford Galaxy - Muting the parking sensors when a trailer or caravan is attached
« on: June 10, 2014, 09:59:51 PM »
« Last Rated on: October 06, 2016, 11:26:51 AM »
This guide talks about how-to install an additional wire to mute the rear parking sensors when you are towing.

Factory fitted tow-bars would have this option installed by default but the parking aid module has the ability regardless. The job is simple enough and requires adding just one wire to the parking aid controller (located under the front passenger seat) to tell the module when a trailer is attached. Again, factory fitted bars have a switch integrated in the plug socket however any latching switch will do, and you can mount this anywhere, switching in "on" when the trailer in connected.

The idea is to ground Pin 5 of connector C77 when the trailer is connected. Access is from behind the passenger seat so start by sliding it all the way forward and removing the mini carpet so you can see the control module. From this angle the connector we want is on the right side as shown below:


Unclip the connector, cut the cable tie off and then slide the inner pin assembly out from the housing whilst depressing the mini-latch at the far end. The pin we need to make is pin 5 and should be empty - if its not then either you have the wrong connector, wrong pin, different module or the car is pre-wired for the towbar! In all but the last case, stop and double check (post here if required!) - if the car is pre-wired then a Brown/Red cable may be in this slot already.


Add your new cable, through a switch and to any ground point and you're done. When its at ground the module interprets this as a trailer being connected and will not operate the rear sensors (The fronts will continue to work).

Finally, test your new switch by trial or by using VCDS and measuring blocks, group 4. Here we can see with the switch not depressed the sounder is active and then again when it is depressed, the trailer becomes "Active" and the sounder stops:


03 Ford Galaxy 1.9 TDI 115 Ghia in Spruce Green Metallic
With cream leather interior, Full Bodykit, Remapped at 145bhp, Lowered on 18's
08 Ford Transit 2.2 TDI 115 in Frozen White
With retrofitted everything except another slidey door! :)

VCDS HEX/CAN - Scans/Coding done in Wiltshire in exchange for winegums! :)



SMF spam blocked by CleanTalk